SL12 Solar Street Light 10W to 25W (With Pole)

Performance
Operating voltage is 24 Volts. DC.
Power consumption is 10, 15, 20 or 25 Watts (subject to model selected).
Operating temperature -40 deg. C ~ +80 deg. C (-40 deg. F ~ 175 deg. F).
Intelligent battery management software to prevent over-charging and over-discharging.
Includes a minimum of three to five days of autonomy (battery back-up).
Several successive cloudy or alternating overcast days typically will not affect illumination time.
The system can operate typically from dusk to dawn or be single or dual timer controlled.
Illumination period can be designed to meet specific requirements.
Supplied solar panel power is based on installation location and system requirements.

Light Fixture
Supplied with a single LED light fixture.
Low profile design with minimal wind resistance.
The fixture is configured with one LED module.
Each LED module contains 14 Philips Luxeon® T LEDs.
Each module has a vented design to increase thermal dissipation.
Can be supplied with a Type I, II, III, IV or V lighting distribution pattern.
Choice of LED color temperature (warm white, daylight white, or cool white). Daylight white is standard.
Warm white is approx. 3,800~4,100k.
Daylight white is approx. 5,000~5,650k.
Cool white is approx. 5,650~6,300k.
Other LED color temperatures are available upon request, or by special order, from 2700k to 6500k and also turtle friendly yellow.
Lumen tolerance +/- 5%.
The 10W luminaire provides approx. 1,850 Lumens (with white LEDs).
The 15W luminaire provides approx. 2,775 Lumens (with white LEDs).
The 20W luminaire provides approx. 3,700 Lumens (with white LEDs).
The 25W luminaire provides approx. 4,625 Lumens (with white LEDs).
Polarity protected circuitry.
LED life is typically up to 100,000 hours or equal to about 22 years.
No bulb changes unlike incandescent street lights.
Fixture attaches to the lamp support arm which in turn attaches to the pole.
Painted aluminum construction with TIR optics.
Silver/gray color anti-static powder coated finish.
Black and custom colors by special order only.
Stainless steel hardware.
IP66 weather rating.
Full cut-off light fixture as specified by IESNA or IES standards.
Dark sky compliant light fixture.
CRI is >75.
LEDs are powered by Mean Well, with integrated PWM Dimming control and multi-driver redundancy.
The light fixture incorporates a high efficiency 18V-32V DC Mean Well LED driver.
The LED driver efficiency is over 90% and is I.P. 65 rated.
The LED driver has short circuit, over current, over voltage and over temperature protection.
The fixture is approx. 17" x 12.5" x 5.5" (43cm x 31cm x 13cm) L x W x D.
The fixture weighs approx. 11.5 lbs (5.3 kgs).
Tenon internal diameter is approx. 2.4" (6cm).
Unique adjustable tenon allows horizontal adjustments from 0-15 degrees and vertical adjustments from 0-15 degrees.
The tenon can be set in a horizontal or vertical position to allow for different support arm angles and pole types.
Certifications, listings and approvals: UL, CE, FCC, RoHS, CB, TUV, CCC, CQC, cULus, ETL, DLC, cETLus, Designlights Consortium, LM79, LM80.

Post / Pole
A choice of a basic 15' (4.5M) pole or a heavy duty 20' (6M) galvanized steel pole is included.
The pole has a square flat base (flat plate) with pre-drilled holes for installation.
The square base of the pole is approximately 12.5" x 12.5" (320mm x 320mm).
Fixing bolts/anchors and templates are included.
Custom height poles are available by special order.
Silver/gray color finish. Custom colors by special order .
The pole diameter will vary depending upon the height. The 20' pole has a diameter of approx. 6" at its base decreasing down to approx. 3" at the top.
Typically the pole requires a concrete foundation up to about 1 cubic yard (3' x 3' x 3'). The location, wind factor and ground condition will affect the size of the foundation required.

Arm
Galvanized steel arm accommodates the light fixture.
Attaches directly to the street light pole.
Choice of arm length available.
Can be attached in any direction and at a choice of height on the pole.
Silver/gray color finish.
Custom colors by special order only.

Battery
24v DC systems use two 12v sealed lead acid, AGM or GEL type rechargeable batteries.
Battery type is deep cycle, marine grade.
Batteries are made in the USA.
Battery capacity is selection is subject to lamp power and illumination duration.
The 32 Amp/Hour AGM battery dimensions are approx. 7.75" x 5" x 7.25" (20cm x 13cm x 18.5cm) LxWxD.
The 32 Amp/Hour AGM battery weighs approx. 24 lbs (17.5 kgs).
The 55 Amp/Hour AGM battery dimensions are approx. 10" x 5.5" x 10" (24cm x 14cm x 25cm) LxWxD.
The 55 Amp/Hour AGM battery weighs approx. 39 lbs (17.5 kgs).
The 79 Amp/Hour AGM battery dimensions are approx. 11" x 7" x 10" (28cm x 17cm x 25cm) LxWxD.
The 79 Amp/Hour AGM battery weighs approx. 53 lbs (24 kgs).
The 92 Amp/Hour AGM battery dimensions are approx. 13" x 6.5" x 9.5" (33cm x 17cm x 24cm) LxWxD.
The 92 Amp/Hour AGM battery weighs approx. 63 lbs (28.5 kgs).
Typical battery life is approximately 5 years subject to environmental factors and autonomy selection.
Please note, if you do not install or use this product for several months the battery may discharge naturally on its own.
By allowing a battery to deep discharge it may cause irreversible damage as the battery may then lose the ability to recharge or hold a full charge.
Periodic charging is always recommended when a product is not being used or when the solar panel is disconnected.
Higher capacity batteries may be required for more demanding applications and/or locations with lower insolation.

Battery Box
Galvanized steel lockable battery box will accommodate the rechargeable batteries. (Padlock not included.)
The battery enclosure can be mounted on to the pole or located at the base of the pole depending installation preference, pole selection, and battery capacity.
The battery box has pre-drilled holes to enable secure installation to a concrete pad.
For pole mounting, the battery enclosure includes mounting plates with slots for U-bolts or Stainless Steel Banding. (U-bolts and Stainless Steel Banding is not included.)
Silver/gray color finish.
Custom colors by special order.

Solar Panel
The solar panel size and power required depends greatly on the installation location and customer’s requirements, please consult our engineers for specific solar power requirements.
Range of solar panel power avalible between 45W and 180W.
Solar panels can be supplied in a dual format (2 x 70w = 140w, 2 x 90w = 180w etc.).
Highly efficient monocrystalline or polycrystalline solar panel with aluminum frame, anti-aging, and encapsulated membrane.
Anti-reflective and anti-soiling surface reduces power losses from dirt and dust.
Certified to withstand high wind loads (340PSI) and snow loads (780PSI); and resistance to high salt and ammonia.
Typical solar panel life is approximately 20-25 years subject to environmental factors.
The dimensions of the solar panel can vary and is subject to the wattage and format supplied.
The solar panel(s) are supplied with steel support frame and T-bar pole mounting system with tenon that allows direct attachment to the top of the pole.
The mounting systems allows the solar panel(s) to be tilted to an appropriate angle determined by the geographic location of the installation site.
The solar panel(s) can be rotated (ideally to a southerly unobstructed view of the sky).
A more powerful solar panel may be required for more demanding applications and/or locations with lower insolation, please consult our engineers for specific solar power requirements.

Control Module
Supplied standard with the most advanced and sophisticated MPPT charge controller technology. The MPPT charge controller automatically controls the solar panel power, battery charging, and lighting function and operation.
Ultra fast Maximum Power Point Tracking (MPPT).
The MPPT charge controller is typically 30% more efficient than standard PWM controllers and 10% more efficient to most other MPPT controllers.
Additional efficiency for cloudy weather and during times of reduced sun radiation.
This controller features the very latest smart technology with intelligent battery management software is used to protect the battery from being excessively discharged.
The controller is sized to the system specifications with 10A and 15A versions available (subject to solar panel power and battery capacity).
This MPPT charge controller is programmed by Solar Illuminations as per your requirements and system ability.
Pre-programmed software for load output, dusk to dawn lighting, single timed lighting, dual timed lighting, dimming option and the ability of interfacing with motion detection, where required.
Lighting control features include illumination from dusk to dawn (where applicable), or on at dusk for X amount of hours then off, or on at dusk for X amount of hours, then off, then back on again for X amount of hours before dawn.
Dimming option (where applicable) allows the lighting to dim at any time during the illumination time.
The dimming option or any other illumination mode can be used in conjunction with motion activation (where applicable).
Dimming may be at any percentage from 1-99%.
Supports real time data monitoring and 30 day memory (iPhone, Android, Mac or PC) with optional interface and/or Bluetooth dongle.
Rated charge current 10A/15A.
Maximum PV power (24V dc) is 270W at 10A and 400W at 15A.
Maximum PV open circuit is 75-100V dc.
Peak efficiency is 98%.
Multi stage adaptive charge algorithm.
Automatic temperature compensation.
Low voltage load disconnect at 11.1V dc to 11.8V dc (12v dc system) or 22.2V dc to 23.6V dc (24V dc system) or battery life algorithm.
Low voltage load reconnect at 13.1V dc to 14V dc (12V dc system) or 26.2V dc to 28V dc (24V dc system).
Protection feature includes battery reverse polarity (fuse), output short circuit and over temperature.
Operating temperature is -22 deg. F (-30 deg. C) to 140 deg. F (+60 deg. C).
Humidity up to 95%, non condensing.
Power terminals are AWG 10 (6mm2).
Protection rating IP22 (connection terminal area).
Weight is 500g (1.1 Lbs).
Dimensions are approx. 4” x 4” x1.5” (10cm x 10cm x 4cm).
Please note: Upon installation and power-up the controller goes into a 7 day evaluation mode where smart monitoring and configurations commence. Additional evaluation with self-managing adjustments may continue for up to 7 more days. This is all part of the smart feature that enables this intelligent controller to understand its use, the application, the surrounding environment and the current conditions. During this time some of its programmed features may differ temporarily. This is a perfectly normal process and must be accepted during that time. During this time the controller will adjust to the current condition and charge status of the batteries. It is therefore recommended that all batteries are 100% fully charged before connection using an appropriate battery charger. This may significantly reduce the evaluation mode time of 7+7 days to much less. The solar panel(s) should be connected to the MPPT charge controller first, followed by the fully charged batteries.

Interconnecting Cable
Connection wiring between the battery box, solar panel and lamp unit is included.

Remarks
We stand behind our lighting systems with one of the best and most comprehensive warranties in the industry. With valid warranty registration, this system is offered with a 10-year limited warranty and the solar panel with a 20-year limited warranty, in accordance with our Terms, Conditions, and Policies. Free, unlimited, lifetime technical support is offered with the warranty.

Please Note:
This product is a special order and is non-returnable except in the event of a fault (during its warranty period) when the product, once returned will be repaired or replaced. The solar panel must be installed in a location where it can receive full direct sunshine (when available) and usually set facing South at an appropriate angle (where adjustment options allow). The solar panel must not be installed in a shaded or part shaded location and never indoors. The standard specifications of the system (particularly the solar panel Wattage and battery capacity) may need to be adjusted. These components are determined by your geographic location, power consumption (LED Wattage) and the total amount of hours of illumination time required. Such changes to the standard specifications may increase or decrease the cost shown. Please contact us for more information or assistance. The illumination time is estimated and subject to various factors including (but not limited to) geographic location, seasons, temperature, weather conditions & location of product etc. The illumination time of most solar lights can reduce during winter months when the weather is poor and the days are shorter. During this time insolation hours decrease accordingly. Shorter illumination time due to one or more of the above factors does not define the product as being ‘defective’ or ‘not as described’. All solar lights must be used in a completely dark location at night time otherwise they may not illuminate. Nearby strong lighting sources or ambient lighting may affect the operation of a solar light. This does not define the product as being 'defective' or 'not as described'. Please note, if you do not install or use this product for several months the battery may discharge naturally on its own. By allowing a battery to deep discharge it may cause irreversible damage as the battery may then lose the ability to recharge or hold a full charge. Although unlikely, we reserve the right to supply this product with any minor alterations or minor changes to the specifications (shown above by text description or by photographs) due to different supplies or product batches received, incorporating such product changes made by the manufacturer, without further notice. Descriptions, specifications and photographs are updated regularly but may not be current when minor changes to a product have only recently been made.

Any concrete work required to facilitate the installation of a pole should not be conducted until all materials have been supplied and have been inspected and verified as being correct and suitable. Solar Illuminations does not accept any responsibility whatsoever for any works carried out in advance, including (but not limited to) ground, excavation, or civil works, pouring or creation of any concrete, cement, etc.

The product specifications above should be used as a general guide. We can offer modifications and changes to the specifications of this product if necessary. This may be required to meet your specific needs and/or due to the geographic location of the installation site. In locations where insolation levels are poor or lower than normal, a higher wattage solar panel and larger capacity batteries may be required. We offer product customization. MPPT, dual timer and dimming charge controllers are all available as optional extras. One or more motion sensors can also be added as an optional extra. Other options included UL listed or ETL certified components and the provision of Buy American Act (BAA & ARRA) compliance, if required. Photometric data, 3D renderings and planning of your lighting project is available. Please contact our sales department for more information before making your purchase.

*View our Terms, Conditions and Polices (including our Returns Policy) for further information.